1, CH- series trough mixer is widely used in pharmaceutical, food, chemical, electronic, mining and other industries dry powder or wet material mixing, so that different proportion of main and auxiliary materials mixed evenly.
2. This model is a through shaft and a mixture of general materials.
型号 | 容积 (m³) | 投料量 (Kg/次) | 外型尺寸 长X高X宽(mm) | 混合时间 (min) | 搅拌转速 (r/min) | 混合电机功率 (KW) | 卸料电机功率 (KW) |
CH-10 | 0.01 | 7 | 1000*450*340 | 6-10 | 28 | 0.55 | 手动 |
CH-20 | 0.02 | 15 | 1050*480*340 | 6-10 | 28 | 0.55 | 手动 |
CH-30 | 0.03 | 23 | 1150*560*400 | 6-10 | 28 | 0.75 | 手动 |
CH-50 | 0.05 | 38 | 1300*1000*540 | 6-15 | 28 | 1.5 | 0.55 |
CH-100 | 0.10 | 83 | 1500*1100*600 | 6-15 | 26 | 2.2 | 0.55 |
CH-150 | 0.15 | 124 | 1660*1120*600 | 6-15 | 24 | 3 | 0.55 |
CH-200 | 0.20 | 90 | 1770*1050*580 | 6-15 | 24 | 4 | 0.55 |
CH-250 | 0.25 | 170 | 1770*1250*600 | 6-15&, lt;, /SPAN> | 24 | 4 | 1.1 |
CH-300 | 0.30 | 210 | 1900*1300*680 | 6-10 | 24 | 5.5 | 1.5 |
CH-400 | 0.40 | 310 | 2200*1350*780 | 6-15 | 20 | 5.5-6级 | 1.5 |
CH-500 | 0.50 | 300 | 2250*1800*780 | 6-15 | 18 | 7.5-6级 | 2.2 |
CH-750 | 0.75 | 560 | 2400*1850*780 | 6-15 | 16 | 7.5-6级 | 2.2 |
CH-1000 | 1.00 | 780 | 2600*1900*800 | 6-15 | 16 | 11-6级 | 3 |
CH-1500 | 1.5 | 1150 | 2800*1950*860 | 6-15 | 12 | 11-6级 | 3 |
CH-2000 | 2.00 | 1500 | 3000*2000*940 | 6-15 | 12 | 15-6级 | 4 |
CH-2500 | 2.50 | 2100 | 3200*2050*1160 | 8-20 | 12 | 18.5-6级 | 5.5 |
CH-3000 | 3.00 | 2250 | 4100*2100*1500 | 8-20 | 10 | 22-6级 | 7.5 |
1, the machine is horizontal groove form: rack, U shaped mixing tank, reducer, motor, mixing, outsourcing and electrical appliances.
2, the whole machine factory, its structure is strong, smooth operation, the material contact is made of high quality stainless steel.
3 、 good corrosion resistance, no dead corners in the tank, smooth and clean groove wall.
4, drive: all adopt triangle belt.
The equipment has been added to the lubricating oil before leaving the factory. After three months of use, the reducer needs to be replaced at once. The lubricating oil (oil number is 20#) will be replaced six months later. The main shaft of the bearing lubricating oil requires high temperature grease lubrication, usually every three months cleaning, replacement, in order to ensure the normal operation of equipment.
The user must check that the parts are normal before use:
First, stir the stirring button to make sure the direction of the mixing is correct (turn the mark on the upper right side of the mixing tank).
1, the amount of material required in accordance with the instructions is appropriate, when work, the upper cover required to cover.
2, unloading should first stop mixing, and then the liquid material to connect quick installation connector unloading, remove the top cover.
3, when cleaning, mixing tank is tilted position, tilt angle is greater than 90 degrees, cleaning and then reset to ensure the service life of equipment seal.
1, after three months of use of the equipment, to check whether the transmission gear loose or wear, lubricating oil has been replaced, etc..
2 、 is the appliance damp?.